27 Oct 2026 5 min read

What Are the Standard Bar Grating Sizes?

Standard bar grating sizes are set by bearing bar size, bearing bar spacing and cross bar spacing, shown in codes such as 19-W-4.

What Are the Standard Bar Grating Sizes?

Bar grating sizes are defined by three measurements: bearing bar dimensions (thickness by height), bearing bar spacing (distance between load-carrying bars), and cross bar spacing (distance between connecting bars). A designation like 19-W-4 means bearing bars are spaced 1-3/16 inches on center with cross bars at 4 inches on center, a shorthand appearing across steel, stainless, and aluminum products from suppliers like AMMS Solutions.

The Size Code Most People Need First

The most common light-duty designation is 19-W-4, the workhorse of industrial flooring. Bearing bars sit 1-3/16 inches apart, cross bars at 4 inches, and bearing bars typically range from 3/4 inch by 3/16 inch up to 2-1/2 inches by 3/16 inch. A 19-W-2 drawing tightens cross bars to 2 inches on center, helping with smaller wheel traffic like hand carts and dollies. A 15-W-4 pattern spaces bearing bars at 15/16 inch on center for higher load capacity without changing bar size.

Heavy-duty grating uses bearing bars from 1 inch by 1/4 inch up to 6 inches by 1/2 inch or larger, handling rolling and static loads at loading docks, airport ramps, and plant floors where forklifts and heavy equipment cross regularly.

Common Panel Widths and Lengths

Stock panels frequently come in 24-inch and 36-inch widths, often 20 feet long (240 inches), then get cut to the exact span needed. Aluminum bar grating sold by linear foot typically appears as 24-inch or 36-inch wide panels, with custom widths and end banding available on request. Panel width runs perpendicular to the bearing bars, while length follows the bearing bar direction and becomes the span.

How the Size Code Breaks Down

Designation

Bearing Bar Spacing

Cross Bar Spacing

Typical Use

19-W-4

1-3/16 in. on center

4 in. on center

Walkways, platforms, general industrial

19-W-2

1-3/16 in. on center

2 in. on center

Smaller wheel traffic, tighter openings

15-W-4

15/16 in. on center

4 in. on center

Higher load capacity, narrower gaps

11-W-4

11/16 in. on center

4 in. on center

Pedestrian areas, small debris concerns

The first number represents bearing bar spacing in sixteenths of an inch: 19 means 19/16, or 1-3/16 inches. The letter indicates construction method (W for welded, P for press-locked, S for swage-locked), and the final number is cross bar spacing in inches.

Material Choices and Their Size Implications

Steel bar grating in carbon steel can be ordered bare, painted black, or hot-dip galvanized. Stainless Steel Grating in 304 or 316 alloys suits corrosive environments, and Aluminium Bar Grating offers corrosion resistance at roughly one-third the weight of steel. Fiberglass Grating and FRP Molded Grating use a different sizing system based on mesh configuration and panel thickness rather than bearing bar dimensions, while FRP Pultruded Grating follows a structural profile approach closer to metal grating logic.

Welded Bar Grating remains the most common construction for permanent installations. Press-Locked Grating uses hydraulic pressure to lock bearing bars and cross bars without welding, creating a smooth appearance popular in architectural settings. Swage-locked grating, common in aluminum, deforms the cross bar into the bearing bar for a rigid connection.

Measuring and Ordering Without Mistakes

Bearing bar size is expressed as thickness first, then height: 3/16 inch by 1 inch means the bar is 3/16 inch thick and 1 inch tall. Panel size is width by length, with length being the span direction. The span runs parallel to the bearing bars, not across them, and getting this backwards is one of the most common ordering errors.

Support placement matters as much as panel size. Bar grating needs support at both ends of the span, and longer spans may need intermediate supports. A grating that deflects under load is usually a span problem, not a bar size problem. Consult load tables for the specific bar size and spacing rather than guessing.

Related Products That Use Different Sizing Logic

Expanded Metal and Standard Expanded Metal are measured by strand width, opening size, and sheet thickness, not bearing bar dimensions. Perforated Metal uses hole diameter, center spacing, and sheet gauge. Grip Strut Grating is a one-piece safety grating with its own channel and plank sizing. Stair Treads built from bar grating follow the same bearing bar conventions but add nosing dimensions and tread depth requirements. Floor Grating and Platform Grating are application terms referencing the same size standards as bar grating, just specified for a particular use.

What to Specify on an Order

State the material, the bar size (thickness by height), the spacing designation, the surface type (smooth or serrated), the panel width and length, and the finish. For example: carbon steel, 3/16 inch by 1 inch bearing bars, 19-W-4 spacing, serrated surface, 36 inches wide by 10 feet long, hot-dip galvanized. Include the span direction and any cutouts or banding requirements. If the grating must meet a specific load or deflection limit, provide that number so the supplier can verify the bar size works for the span.

Request a Quote

Frequently Asked Questions

Specify material, bearing bar size as thickness by height, spacing designation (such as 19-W-4), panel width and length with span direction, surface type, and finish. Include any load requirements, cutouts, or banding needs.

Unit weight depends on bar size, spacing, and material. A 3/16 inch by 1 inch bar in 19-W-4 steel grating weighs roughly 8 to 10 pounds per square foot, while the same configuration in aluminum weighs about one-third as much. Suppliers publish weight tables for each size and material combination.

It means bearing bars are spaced 19/16 inches (1-3/16 inches) on center, the W indicates welded construction, and cross bars are spaced 4 inches on center. This is the most common light-duty industrial grating pattern.

Support the grating at both ends of the span, with bearing bars running parallel to the span direction and resting on the support structure. Longer spans may need intermediate supports, and the support surface should be flat and level to prevent rocking or point loading.
Tags: bar grating sizes standard bar grating sizes 19-W-4 grating bar grating welded bar grating press-locked grating aluminium bar grating stainless steel grating grating specifications
Share this article: LinkedIn Twitter