Cut-to-size grating panels are standard grating sheets or bars trimmed to your exact dimensions before they leave the supplier, so the panel arrives ready to lay into a frame, trench, platform, or stair opening without further on-site cutting. The service typically covers welded bar grating, press-locked grating, aluminum, stainless steel, fiberglass, and expanded metal, with dimensional tolerances held to around plus or minus 1 mm depending on the material and cutting method. For buyers who need a precise fit on a tight installation schedule, cut-to-size panels remove the most common source of field errors: measuring wrong, cutting crooked, or damaging the galvanized edge.
What the Service Actually Covers
A proper cut-to-size order involves more than trimming length and width. The supplier should also address edge treatment, because a raw cut edge on galvanized steel exposes the base metal and can leave the panel weaker at the perimeter. Welded edge banding is the standard fix for bar grating. It closes the open bar ends, keeps bars from spreading under load, and restores a clean bearing line for the panel to sit on its support steel. On press-locked and swage-locked grating, banding is less critical because the bars are already mechanically locked, but it is still specified on panels that will be lifted or walked on frequently.
Cutting methods matter too. CNC plasma and waterjet cutting produce clean, repeatable edges on steel and aluminum, while fiberglass panels are normally cut with diamond or carbide tooling to avoid delaminating the resin matrix. A supplier that offers both cutting and banding under one roof, as AMM Solutions does, can hold tighter accountability for the finished dimension than one that farms out secondary processing.
Grating Types That Work Well Cut to Size
Not every grating product is equally suited to custom sizing. The table below summarizes the main options.
Grating Type | Best For | Custom Sizing Notes |
Welded Bar Grating | Heavy platforms, mezzanines, trench covers | Needs welded edge banding after cutting |
Press-Locked Grating | Architectural work, clean sightlines | Holds shape well; banding optional |
Aluminum Bar Grating | Wet areas, lightweight access | Cut with carbide or waterjet; no hot work |
Stainless Steel Grating | Food, pharmaceutical, corrosive washdown | More expensive to cut; verify passivation after cutting |
FRP Molded Grating | Chemical plants, offshore walkways | Cut with diamond tooling; seal cut edges |
Expanded Metal | Ramps, guards, infill panels | Standard Expanded Metal sheets cut to size; edge flattening available |
Grip Strut Grating | Stair treads, ramps, safety walkways | Serrated surface; cutting must preserve slip resistance |
For most industrial walkways, Welded Bar Grating remains the default because it carries heavy point loads and the banding detail is well understood. Press-Locked Grating is preferred where appearance matters or where the panel must sit flush in a visible architectural frame. Aluminium Bar Grating suits wet or marine environments, while Stainless Steel Grating is the choice for washdown areas in food plants. Fiberglass Grating, including FRP Molded Grating and FRP Pultruded Grating, is specified where corrosion or electrical isolation rules out metal entirely.
Measurement Requirements
The most common mistake on cut-to-size orders is measuring the opening rather than the bearing surface. Grating panels sit on support steel, so the panel dimension should be measured from the inside face of one bearing bar support to the inside face of the opposite support, minus a small clearance allowance. A typical clearance is 3 to 6 mm on each side for metal grating, slightly more for fiberglass because it expands and contracts with temperature.
If the existing frame is out of square, take measurements at both ends and the middle, then supply the smallest workable dimension. A panel cut square will not drop into a trapezoidal opening. For replacement panels, always measure the removed panel rather than the hole, but check the old panel for bowing or bar spread before trusting those numbers.
Other details to confirm before ordering: bar direction and span direction, bearing bar depth and thickness, mesh or aperture size, surface finish, and whether the panel needs a specific banding height. On Floor Grating and Platform Grating used in public or regulated spaces, load rating and deflection criteria should be stated on the order.
Ordering Considerations and Minimums
Non-standard cut-to-size panels are made against a specific order, so minimum order quantities are common. The threshold varies by material and supplier, but buyers should expect a higher minimum on custom fiberglass panels than on cut steel grating, simply because the raw sheet sizes and cutting economics differ. Ordering several identical panels at once is the most practical way to meet minimums and reduce unit cost.
Lead time depends on whether the panel is cut from stock sheet or produced from scratch. Stock sheet cutting is usually fast. Custom bar depth, unusual alloys, or special coating after cutting extends the schedule. If the panel will be hot-dip galvanized after fabrication, allow for the galvanizing cycle and specify that cut edges must be cleaned and prepared before dipping.
Perforated Metal and Expanded Metal panels follow a similar logic but with different edge rules. Standard Expanded Metal is often sheared to size and left with a flattened or unflattened edge depending on the application. Perforated Metal may need an unperforated margin around the perimeter for fixing.
What to Ask Before You Order
A short list of practical questions will catch most ordering problems. Ask whether the quoted dimension is the finished panel size or the pre-cutting blank size. Ask who is responsible for edge banding and whether it is included or priced separately. Ask what tolerance the supplier guarantees and how they verify it. Ask whether the cut edges on galvanized or coated material will be touched up, and with what product. Ask for a cutting drawing or confirmation sketch before production begins, especially on panels with notches, corner cutouts, or pipe penetrations.
For Stair Treads, the same principles apply but the tread must also match the stringer spacing and nosing detail. A tread cut to the wrong width is not a minor trim job; it is scrap.
AMMS Global supplies cut-to-size grating panels across welded, press-locked, aluminum, stainless, and fiberglass lines, with welded edge banding and CNC cutting as standard on custom orders. The practical takeaway is to treat the cut-to-size order as a fabrication service, not a simple stock cut. Provide bearing dimensions, confirm the span direction, specify the edge treatment, and review the cutting drawing before the material goes to the saw.
What is the standard size of grating panels?
Standard steel grating panels are commonly produced in widths of around 900 to 1000 mm and lengths up to 6000 mm, but cut-to-size service exists precisely because real openings rarely match those modules. Fiberglass molded panels are typically 1000 by 3000 mm or 1220 by 3660 mm, while expanded metal and perforated metal sheets follow their own mill sizes.
Can you cut grating panels on site?
Yes, but field cutting is slower, less accurate, and often damages galvanized or coated edges. On-site cutting also creates hot work permits and sparks on steel grating. Cut-to-size panels from the supplier avoid those issues and arrive with finished, banded edges.
What tolerance can I expect on cut-to-size grating?
A tolerance of plus or minus 1 mm is realistic for CNC-cut steel, aluminum, and stainless grating. Fiberglass panels are usually quoted slightly wider, often plus or minus 3 mm, because the material moves during cutting and temperature changes. Confirm the tolerance before ordering and ask how it is verified.
Does cut-to-size grating cost more than stock panels?
It usually involves a cutting charge and possibly a minimum order quantity, but the total installed cost can be lower once field labor, scrap, and rework are counted. The economics improve when several panels share the same dimensions.
Do cut edges need treatment on galvanized grating?
Yes. Cutting exposes bare steel at the edge. The standard fix is welded edge banding, which covers the bar ends and restores corrosion protection after the panel is fabricated. Cold galvanizing compound can touch up small areas, but banding is the structural and practical solution.